Noco Genius 5 How To Use

NOCO Genius5 Smart Bombardment Charger User Guide

NOCO Genius5 Smart Battery Charger User Guide

DANGER

READ AND UNDERSTAND ALL Prophylactic Data Before USING THIS Production. Failure to follow these rubber instructions may outcome in ELECTRICAL Daze, EXPLOSION, Fire, which may consequence in a SERIOUS INJURY, Decease, or PROPERTY DAMAGE.

Electrical Shock. Production is an electric device that tin can shock and cause serious injury. Do non cut ability cords. Practise not submerge in water or go moisture.

Explosion. Unmonitored, incompatible, or damaged batteries tin explode if used with product. Practice non leave product unattended while in use. Exercise not attempt to spring start a damaged or frozen battery. Utilize product only with batteries of recommended voltage. Operate product in well ventilated areas.

Burn down. Production is an electrical device that emits heat and is capable of causing burns. Do not cover product.
Do non smoke or employ any source of electrical spark or burn down when operating production. Go on product away from combustible materials.

Eye Injury. Wear eye protection when operating product. Batteries tin explode and cause flight debris.
Bombardment acid tin cause eye and skin irritation. In the case of contagion of optics or pare, flush affected area with running clean water and contact poison control immediately.

Explosive Gases. Working in the vicinity of a lead-acid is dangerous. Batteries generate explosive gases during normal bombardment operation. To reduce risk of battery explosion, follow all safety information instructions and those published by the bombardment manufacturer and manufacturer of whatsoever equipment intended to be used in the vicinity of battery. Review cautionary markings on these products and on engine.

Of import Safe Warnings

• About GENIUS5. The NOCO GENIUS5 represents some of the most innovative and advanced technology on the marketplace, making each charge simple and easy.
• It is quite possibly the safest and about efficient charger you will ever apply. The GENIUS5 is designed for charging all types of 6V & 12V pb-acid batteries, including Lithium (LiFePO4), Wet (Flooded), Gel, MF (Maintenance-Free), CA (Calcium), EFB (Enhanced Flooded Battery), and AGM (Absorption Glass Mat) batteries.
• It is suitable for charging battery capacities upwards to 120 Amp-Hours and maintaining all bombardment sizes.
• Getting Started.  Before using the charger, advisedly read the bombardment manufacture'due south specific precautions and recommended rates of charge for the battery.
• Make certain to make up one's mind the voltage and chemistry of the battery by referring to your battery possessor's manual prior to charging. Mounting.
• It is of import to keep in mind the distance to the battery.
• The DC cablevision length from the charger, with either the bombardment clamp or eyelet terminal connectors, is approximately 77.7-inches (1973.6mm). Allow for 12-inches (304mm) of slack betwixt connections. Proposition 65.
• Battery posts, terminals, and related accessories comprise chemicals, including lead.
• These materials are known to the State of California to cause cancer and nativity defects and other reproductive harm. Personal Precaution.
• Only use product as intended. Someone should be within range of your phonation or shut enough to come to your help in instance of emergency. Take a supply of clean water and soap nearby in the case of battery acid contamination.
• Wear complete eye protection and protective clothing while working near a battery.
• Always wash easily after handling batteries and related materials.
• Do not handle or wear whatsoever metal objects when working with batteries including; tools, watches or jewelry. If metallic is dropped onto battery, it may spark or create a curt excursion resulting in electric shock, fire, explosion which may upshot in injury, death or holding damage. Minors.
• If the production is intended by "Purchaser" to exist used by a pocket-size, purchasing adult agrees to provide detailed instructions and warnings to whatsoever small prior to utilize.
• Failure to do and then is the sole responsibility of the "Purchaser," who agrees to indemnify NOCO for any unintended utilise or misuse by a minor. Choking Hazard. Accessories may present a choking risk to children.
• Do non leave children unattended with production or whatsoever accessory.
• The production is non a toy. Handling. Handle production with care. The product tin can become damaged if impacted.
• Do not utilize a damaged product, including, but not limited to, cracks to the casing or damaged cables.
• Exercise not use production with a damaged power cord. Humidity and liquids may damage product.
• Do not handle production or any electrica components nigh any liquid. Store and operate product in dry locations.
• Do not operate product if information technology becomes wet.
• If product is already operating and becomes wet, disconnect it from the battery and discontinue use immediately.
• Do not disconnect the production by pulling on the cables. Modifications.
• Practise not endeavor to change, modify or repair any part of the product.
• Disassembling production may cause injury, decease or damage to property. If production becomes damaged, malfunctions or comes in contact with whatever liquid, discontinue use, and contact NOCO. Any modifications to the product will void your warranty. Accessories. This product is only approved for employ with NOCO accessories. NOCO is not responsible for user safety or damage when using accessories not canonical by NOCO. Location. Prevent battery acid from coming in contact with the product.
• Do not operate the product in a airtight-in area or an surface area with restricted ventilation.
• Exercise not set up a bombardment on top of product. Position cable leads to avert accidental harm by moving vehicle parts (including hoods and doors), moving engine parts (including fan blades, belts, and pulleys), or what could become a hazard that may cause injury or death. Operating Temperature. This production is designed to work in ambient temperatures between -4° F and 104° F (-xx° C and 40° C).
• Do not operate outside of temperature ranges.
• Do not charge a frozen bombardment. Discontinue use of product immediately if the battery becomes excessively warm. Storage.
• Practise not utilise or store your production in areas with loftier concentrations of dust or airborne materials. Store your product on flat; secure surfaces so it's not prone to falling. Store your product in a dry location.
• The storage temperature is -20° to 25°C (boilerplate under-hood temperature). Never exceed 80ºC nether any condition. Compatibility. The production is only compatible with 6V & 12-volt Lead-Acid, AGM, and Lithium batteries.
• Do not attempt to utilise product with any other type of bombardment. Charging other battery chemistries may event in injury, death or property impairment. Contact the bombardment manufacturer prior to attempting to charge the bombardment. Medical Devices.
• Do not accuse pacemakers or other medical devices. Product may emit electromagnetic fields. Production contains magnetic components which may interfere with pacemakers, defibrillators, or other medical devises.
• These electromagnetic fields may interfere with pacemakers or other medical devices.
• Consult with your physician prior to employ if you have whatever medical device including pacemakers. If you suspect the product is interfering with a medical device, stop using the product immediately and consult your doctor.
• Cleaning Power off the product earlier attempting any maintenance or cleaning. Clean and dry out product immediately if it comes in contact with liquid or any type of contaminant. Use a soft, lint-free (microfiber) cloth. Avoid getting wet in openings. Explosive Atmospheres. Obey all signs and instructions.
• Do non operate production in any expanse with a potentially explosive temper, including fueling areas or areas which contain chemicals or particles such every bit grain, grit or metal powders. High-Event Activities.
• This product is not intended for use where the failure of the production could pb to injury, death or astringent environmental impairment. Radio Frequency Interference. Product is designed, tested, and manufactured to comply with regulations governing radio frequency emissions. Such emissions from the product tin negatively affect the operation of other electronic equipment, causing them to malfunction. Model Number: Genius5 This device complies with Role 15 of the FCC Rules.
• Operation is field of study to the following two conditions: (ane) this device may non cause harmful interference, and (2) this device must have any interference received, including interference that may cause undesired operation.
  Notation: This equipment has been tested and constitute to comply with the limits for a Class A digital device, pursuant to Function 15 of the FCC Rules. These limits are designed to provide reasonable protection confronting harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and tin radiate radio frequency energy and, if not installed and used in accord with the educational activity manual, may cause harmful interference to radio communications. Operation of this equipment in a residential surface area is likely to crusade harmful interference in which example the user will be required to correct the interference at his/her own expense.

How To Use

Charging Modes.
The GENIUS5 has 7 (7) modes: Standby, 12V, 12V AGM, 12V LITHIUM, 6V, REPAIR and Forcefulness. Some charge modes must be pressed and held for three (3) to five (5) seconds to enter the style. These "Press and Hold" modes are advanced charging modes that require your full attention before selecting. It is important to understand the differences and purpose of each charge mode. Do not operate the charger until you lot confirm the appropriate accuse mode for your battery. Beneath is a cursory description:

Mode	Explanation (Peak Voltage Measured At 25°C, Amperage Rating Is Bulk Amperage When Higher up 0°C)
Standby	In Standby way, the charger is not charging or providing any power to the battery. Energy Save is activated during this style, drawing microscopic ability from the electric outlet. Canbus is enabled in Standby style. When in Standby, the orange Standby LED volition illuminate. No Power
12 V	For charging 12-volt Moisture Jail cell, Gel Cell, Enhanced Flooded, Maintenance-Gratis and Calcium batteries. When selected, the 12V white LED volition illuminate. 14.5V | 5A | Up To 120Ah Batteries
12 V AGM	For charging 12-volt AGM batteries. When selected, the 12V AGM white LED will illuminate. 14.8V | 5A | Upward To 120Ah Batteries
12 Five LITHIUM	For charging 12-volt lithium-ion batteries, including lithium iron phosphate. When selected, the 12V Lithium blue LED volition illuminate. For use on batteries with Bombardment Management Systems (BMS) only.  xiv.6V | 5A | Up To 120Ah Batteries
6V Press & Hold (3 Seconds)	For charging 6-volt Moisture Prison cell, Gel Cell, Enhanced Flooded, Maintenance-Gratuitous and Calcium batteries. When selected, the 6V white LED will illuminate. 7.25V | 5A | Upwards To 120Ah Batteries
Force Style Printing & Hold (5 Seconds)	For charging batteries with a voltage lower than 1V. Printing and Concord for five (5) seconds to enter Forcefulness Mode. The selected charge fashion volition then operate under Strength Mode for 5 (5) minutes before returning to standard charging in the selected way. 5A | Upward To 120Ah Batteries
12 5 REPAIR	An advanced battery recovery mode for repairing and restoring, old, idle, damaged, stratified or sulfated batteries. When selected, a carmine LED will illuminate and wink.
	16.5V | 5A | Any Capacity [From Standby Press and Hold 3 Seconds With Clamps Connected to the Battery]

Using 6V. [Press & Hold for 3 seconds]
6V charge way is designed for 6-volt lead-acid batteries but, like Moisture Cell, Gel Cell, Enhanced Flooded, Maintenance-Free and Calcium batteries. Press and hold for iii (three) seconds to enter 6V Charge Mode. Consult the battery manufacturer before using this mode.

Using 12V Lithium.
12V Lithium charge mode is designed for 12-volt lithium-ion batteries simply, including lithium iron phosphate

CAUTION. USE THIS MODE WITH EXTREME Intendance. THIS Style SHOULD Just BE USED WITH 12-VOLT LITHIUM BATTERIES THAT Take A Built-IN Battery MANAGEMENT Organization (BMS). LITHIUM ION BATTERIES ARE Made AND Constructed IN Dissimilar Means AND SOME MAY OR MAY Not CONTAIN A BATTERY Direction Organisation (BMS). CONSULT THE LITHIUM Bombardment MANUFACTURER Before CHARGING AND ASK FOR RECOMMENDED CHARGING RATES AND VOLTAGES. SOME LITHIUM-ION BATTERIES MAY BE UNSTABLE AND UNSUITABLE FOR CHARGING.

Forcefulness Mode. [Printing & Hold for v seconds]
Force mode allow the charger to manually brainstorm charging when the connected battery's voltage is too low to be detected. If battery voltage is too low for the charger to detect, press and hold the mode button for 5 seconds to activate Force Mode, and then select the appropriate style. All available modes volition wink. Once a charge mode is selected, the Charge Way LED and Charge LED will alternating between each other, indicating Force Mode is active. Afterward five (5) minutes the charger will return to the normal charge operation and depression voltage detection will be reactivated.

Caution. Utilize THIS MODE WITH EXTREME CARE. Strength MODE DISABLES Prophylactic FEATURES AND Live Ability IS Present AT THE CONNECTORS. ENSURE ALL CONNECTIONS ARE Fabricated PRIOR TO ENTERING FORCE Mode, AND Practice NOT TOUCH CONNECTIONS TOGETHER. Take a chance OF SPARKS, FIRE, EXPLOSION, PROPERTY Impairment, INJURY, AND Death.

Using 12V Repair. [From Standby Press and Hold 3 Seconds With Clamps Connected to the Battery]
12V Repair is an avant-garde battery recovery manner for repairing and storing, old, idle, damaged, stratified or sulfated batteries. Not all batteries can be recovered.
Batteries tend to become damaged if kept at a low accuse and/or never given the opportunity to receive a full accuse. The most common battery problems are bombardment sulfation and stratification. Both battery sulfation and stratification volition artificially heighten the open circuit voltage of the battery, causing the bombardment to announced fully charged, while providing low capacity. Use 12V Repair in attempt to reverse these problems. For optimal results, accept the 12-volt battery through a full charge cycle, bringing the battery to full accuse, before using this way. 12V Repair tin have up to iv (4) hours to complete the recovery procedure and will return to Standby when completed.

CAUTION. USE THIS Fashion WITH Intendance. THIS Way IS FOR 12-VOLT Atomic number 82-Acrid BATTERIES ONLY. THIS MODE USES A HIGH CHARGING VOLTAGE AND MAY CAUSE SOME WATER LOSS IN WET (FLOODED) CELL BATTERIES. BE Brash, SOME BATTERIES AND ELECTRONICS MAY BE SENSITIVE TO HIGH CHARGING VOLTAGES. TO
MINIMIZE RISKS TO ELECTRONICS, DISCONNECT THE Battery BEFORE USING THIS Fashion.

Connecting to the Bombardment.
Exercise not connect the AC power plug until all other connections are made. Identify the correct polarity of the battery terminals on the battery. Practice non brand whatever connections to the carburetor, fuel lines, or thin, sheet metal parts. The beneath instructions are for a negative basis arrangement (most mutual). If your vehicle is a positive ground arrangement (very uncommon), follow the below instructions in reverse social club.

1. Connect the positive (ruddy) eyelet last connector to the positive (POS,P,+) battery final.
2. Connect the negative (black) eyelet terminal connector to the negative (NEG,N,-) battery terminal.
3. Connect the battery charger into a suitable electric outlet. Practice not face the battery when making this connection.
4. When disconnecting, disconnect in the opposite sequence, removing the negative first (or positive commencement for positive basis systems).

Begin Charging.

1. Verify the voltage and chemistry of the battery.
2. Confirm that you have connected the bombardment clamps or eyelet last connectors properly and the AC power plug is plugged into an electric outlet.
3. [First time use] The charger can at present be left continued to the battery at all times to provide maintenance charging.
4. Press the mode push button to toggle to the appropriate accuse style (press and concord for three seconds to enter an advanced charge style) for the voltage and chemistry of your battery.
5. The manner LED will illuminate the selected charge mode and the Charge LEDs will illuminate (depending on the wellness of the bombardment) indicating the charging
   procedure has started.
6. The charger can now be left connected to the battery at all times to provide maintenance charging.

Auto-Retention: The charger has built in auto-memory and volition return to the last charge mode when continued. To change modes later on the kickoff use, press the fashion push.

Charging Times

Charging Times.
The estimated time to charge a battery is shown below. The size of the battery (Ah) and its depth of discharge (DOD) greatly impact its charging time. The charge time is based on an boilerplate depth of belch to a fully charged bombardment and is for reference purposes only. Actual information may differ due to bombardment conditions. The fourth dimension to charge a normally discharged bombardment is based on a 50% DOD. Temperature volition also impact charging times. The GENIUS5 features thermal bounty that automatically adjusts charging profiles to maximize charging functioning.

Battery Size Ah (Amp hour)	Approximate Time to Charge In Hours 6V                                        12V
xx	3.0	3.0
xl	half dozen.0	6.0
80	12.0	12.0
100	fifteen.0	15.0
120	xviii.0	eighteen.0

Understanding Charge LEDs.

LED	Explanation
25% Ruby LED	The 25% Charge LED will slowly pulse "on" and "off", when the battery is less than 25% fully charged. When the battery is 25% charged, the red Charge LED will be solid.
50% Cerise LED	The 50% Charge LED will slowly pulse "on" and "off", when the battery is less than fifty% fully charged. When the bombardment is 50% charged, the crimson Charge LED will be solid.
75% Orange LED	The 75% Charge LED will slowly pulse "on" and "off", when the battery is less than 75% fully charged. When the battery is 75% charged, the orange Charge LED will exist solid.
100% Green LED	Pulsing Dark-green LED – Bulk accuse complete, optimizing battery for extended life. Solid Green LED – When the bombardment is 100% charged, the Charge LED will be solid green.
Maintenance Green LED	Subsequently the battery is fully charged, the charger will proceed monitoring the battery, and provide ongoing maintenance and optimization. The 100% Charge LED will pulse "on" and "off" slowly during these cycles. The charger can be left connected to the battery indefinitely.

Agreement Error LEDs.
Error Conditions volition exist indicated past the following LEDs.

LED	Reason/Solution
Solid	Charger is in Standby mode or Battery voltage is too low for charger to detect.
Solid	Bombardment voltage is likewise high for the selected charge mode. Cheque the battery and charge mode.
Solid	Possible bombardment short / Battery will non concord a charge. Have battery checked by a professional.
Solid	Reverse polarity. Reverse the bombardment connections.
Flashing	Charger internal temperature too high / Charger will resume role once the Charger internal temperature drops. Charger ambient temperature also cold / Charger will resume function one time the Charger ambience temperature rises.

Production Overview

1. Mode Button Push to cycle through charging Modes.
2. Overvoltage Error LED Illuminates solid Red; Battery Voltage is above
   Protect voltage.
3. BadBattery Error LED Illuminates solid Carmine when connected battery volition not concord a accuse.
4. Reverse Polarity Fault LED Illuminates solid Cherry-red when reverse polarity is detected.
5. Charge LED indicates the connected battery(s) state-of-charge.
6. Standby LED Illuminates when the charger is in Standby Mode, the charger is not charging or providing any power to the bombardment.
7. Repair Mode LED Illuminates solid Red when Repair mode is selected.
8. Printing and Agree» Mode LED Mode push button must be pressed and held for 3 seconds to enter the manner.
9. Mode LED Indicates the Charge Fashion the charger is currently in. Push the MODE button to cycle through charge Modes.

Technical Specifications

• Input Voltage AC: 120-240 VAC, l-60Hz
• Working Voltage Ac: 120-240 VAC, 50-60Hz
• Output Ability: 75 W Max
• Charging Voltage: Various
• Charging Electric current: 5A (12V), 5A (6V)
• Low-Voltage Detection: 1V (12V), 1V (6V)
• BackCurrent Drain: <0.5mA
• Ambient Temperature: -20°C to +40°C
• Type of Batteries: 6V, 12V
• Bombardment Chemistries: Wet, Gel, MF, CA, EFB, AGM, Calcium, Lithium
• Battery Capacity: Upward to 120Ah, Maintains All Battery Sizes
• Housing Protection: IP65
• Cooling: Natural Convection
• Dimensions (L x W x H): iv.half dozen ten ii.9 x 1.9 Inches
• Weight: ane.5 Pounds

iii Year Hassle-Free Warranty

NOCO warrants that this product (the "Product") will be free from defects in textile and workmanship for a period of 3 (iii) years from the date of purchase (the "Warranty Menses"). For defects reported during the Warranty Menstruation, NOCO volition, at its discretion, and subject area to NOCO'due south technical support analysis, either repair or replace lacking products. Replacement parts and products will exist new or serviceably used, comparable in function and operation to the original office and warranted for the remainder of the original Warranty Period.

NOCO'S LIABILITY HEREUNDER IS EXPRESSLY LIMITED TO REPLACEMENT OR REPAIR. TO THE MAXIMUM EXTENT PERMITTED By Police, NOCO SHALL Not BE LIABLE TO Whatever PURCHASER OF THE Product OR ANY THIRD PARTY FOR Whatsoever SPECIAL, INDIRECT, CONSEQUENTIAL OR EXEMPLARY DAMAGES, INCLUDING, BUT Not Express TO, LOST PROFITS, PROPERTY Harm OR PERSONAL INJURY, RELATED IN ANY WAY TO THE PRODUCT, HOWSOEVER CAUSED, Fifty-fifty IF NOCO HAD Knowledge OF THE POSSIBILITY OF SUCH DAMAGES. THE WARRANTIES SET Forth HEREIN ARE IN Lie OF ALL OTHER WARRANTIES, Limited, Unsaid, STATUTORY OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A Particular PURPOSE, AND THOSE ARISING FROM Form OF
DEALING, USAGE OR Trade Exercise. IN THE EVENT THAT ANY APPLICABLE LAWS IMPOSE WARRANTIES, Weather condition OR OBLIGATIONS THAT CANNOT Be EXCLUDED OR MODIFIED, THIS PARAGRAPH SHALL Employ TO THE GREATEST EXTENT ALLOWED BY SUCH LAWS.

This Warranty is made solely for the benefit of the original purchaser of the Product from NOCO or from a NOCO approved reseller or distributor and is non assignable or transferable. To assert a warranty merits, the purchaser must: (i) asking and obtain a render merchandise authorisation ("RMA") number and return location data (the "Return Location") from NOCO Support by emailing [email protected] or past calling 1.800.456.6626; and (2) send the Product, including RMA number, and receipt to the Return Location. Exercise NOT SEND IN PRODUCT WITHOUT FIRST OBTAINING AN RMA FROM NOCO SUPPORT.

The original purchaser is responsible (and must prepay) all packaging and transportation costs to ship products for warranty service.

NOTWITHSTANDING THE ABOVE, THIS HASSLE-Complimentary WARRANTY IS VOID AND DOES Not APPLY TO PRODUCTS THAT: (a) are misused, mishandled, subjected to abuse or devil-may-care handling, accident, improperly stored, or operated under weather condition of farthermost voltage, temperature, shock, or vibration across NOCO's recommendations for safe and effective use; (b) improperly installed, operated or maintained; (c) are/were modified without the express written consent of NOCO; (d) take been disassembled, contradistinct or repaired by anyone other than NOCO; (e) the defects of which were reported after the Warranty Period.

THIS HASSLE-FREE WARRANTY DOES NOT Encompass: (1) normal clothing and tear; (2) corrective damage that does not affect functionality; or (3) Products where the NOCO serial number is missing, contradistinct, or defaced.

HASSLE-FREE WARRANTY CONDITIONS
These conditions utilize only to Product during the Warranty Period. The Hassle-Free Warranty is void either past elapsed fourth dimension from date of buy (elapsed time from serial number date, if no proof of buy) or from the conditions listed earlier in this certificate. Return Product with the advisable documentation.

With Receipt:
0-3 Years: NO Charge. With proof of purchase, The warranty period begins on date of purchase.

With NO Receipt:
0-three Years: NO Charge. With NO proof of purchase, The warranty period begins on the serial number date.

We recommend registering your NOCO product in social club to upload proof of buy and extend your effective warranty dates. Yous may register your NOCO product online at: no.co/register. If you have any questions regarding your warranty or product, contact NOCO Support (email and phone number above) or write to: The NOCO Company, at 30339 Diamond Parkway, #102, Glenwillow, OH 44139 U.s.a..

FAQS

Do axtra battery charger amend than noco genius v? axtra battery charger merely cost $30?

Typically y'all get what you paid for with a battery charger. Cheap chargers accept cheap controls & tend to overcharge batteries, which tin can easily add up to a $100 expense to supervene upon the bombardment.

Tin you apply this to "jump start" a dead machine bombardment?

No, the GENIUS5 is non a jump starter. It is a battery charger/maintainer simply.

Will the charger bleed the battery if the Air conditioning power fails?

No, the dorsum electric current describe is negligible – less than 0.5mA.

Volition this work for large agm auto batteries with 850a? or large marine deep cycles?

The GENIUS5 volition work to charge AGM batteries that are 120Ah or less in chapters.

Is this charger suitable for lithiun- Ion Batteries?

Yes.

Does this piece of work with 120v ac and tin it charge a 100ah agm?

Yeah.

Will it repair/desulfate a duracell half dozen volt gc2 golf game cart battery?

Yes, the 6-volt charge mode includes a desulfation stage that helps repair 6-volt batteries.

tin can items similar nuance cam be operating while charging?

Yes, equally long as the load does not exceed 5A.

dose it have a auto close off?

Aye. It's a fully-automated bombardment charger that will shut-off when fully charged.

Is this an 8 step charger?

Yes.

Tin can this charge Wheelchair battery?

Equally long equally it runs on 6V and/or 12V charges, it should work.

Is this a high frequency charger, or every bit good as one?

We use a proprietary algorithm that uses high-frequency, high-voltage, and other methodologies.

how does it charge?

The GENIUS5 is a battery charger that recharges a bombardment just when plugged into an A/C outlet. It is non a leap starter. See NOCO Boost UltraSafe Lithium Leap Starters.

Will this work with a 12v 550cca 65amp hour deep cycle marine battery?

Yes, but for a battery of 65amp past hour, it charges this bombardment between 6 and 9 hours.

no.co/genius

Documents / Resources

References

• NOCO

Source: https://manuals.plus/noco/genius5-smart-battery-charger-manual

Share this post